Remove the factory default address from eth0/bond0.
By default, Address Manager and DNS/DHCP Server ship with the factory default IPv4 address of 192.168.1.1 on the eth0 interface; this is also the default Primary Service IP.
For most customers, this default IP address will be removed by setting a new IPv4 address on eth0 during the initial set-up and configuration of the appliance or VM; the newly assigned IPv4 address on eth0 also becomes the new Primary Service IP.
BlueCat advises extreme caution if attempting to change the Service interface associated with the Primary IP address (for example, if the Service interface and Primary IP are configured on eth0, but you want to configure the Service interface on VLAN eth0.100). Changing the Service interface may result in a restart of all running services. That is, changing the Service interface may result in a restart of services running on additional IP addresses, loopback addresses, and VLAN interfaces.
To remove the factory default address:
If performing a clean/new server installation, steps 1 and 2 aren't required; go to step 3.
From the DNS/DHCP Server Administration Console, remove the server
from Address Manager control.
Adonis> configure system Adonis:configure:system> set state no-proteus-control
From the DNS/DHCP Server Administration Console, run the reset
factory-default command to remove all IP addresses and
Note: The reset factory-default command isn't supported on the bond0 interface. You must first run the remove bond0 command from Interface configuration mode, then run the modify eth0 and reset factory-default commands.Warning: Run the reset factory-default command with extreme caution. Running this command will delete ALL IPv4 and IPv6 addresses and VLAN interfaces and bonding interfaces configured on the selected interface and restore factory defaults. This action is irreversible.
Adonis> configure interfaces Adonis:configure:interfaces> modify eth0 Adonis:configure:interface:eth0> reset factory-default All configurations for this interface will be set to factory default. Please confirm to proceed(Y/y or N/n)? y Successfully reset the interface to factory default
Add new VLAN interfaces.
Note: If you require NIC bonding/network redundancy on top of VLAN interfaces, you must configure bonding before creating VLANs. For details, refer to Configuring DNS/DHCP Server network redundancy from the Administration Console.
Adonis> configure interfaces Adonis:configure:interfaces> add vlan-interface vlan-id <1> parent <eth0|bond0>
Assign IP addresses to the newly created VLAN interfaces or the bonding
Adonis> configure interfaces Adonis:configure:interfaces> modify <vlan-interface|bond0> Adonis:configure:interface:vlan-interface> add address <ipv4|ipv6address/ netmask>
Set a new Primary Service IPv4 address using an IPv4 address assigned to one of
your newly created VLAN interfaces. You can also set a new Primary Service IPv6
address if necessary.
Adonis> configure interfaces Adonis:configure:interfaces> modify <vlan-interface|bond0> Adonis:configure:interface:vlan-interface> set primary <ipv4|ipv6address> Adonis:configure:interface:vlan-interface> save Saved interface successfully This operation will disconnect SSH connections.
Remove the IPv4 address 192.168.1.1 from eth0/bond0 interface.
Adonis> configure interfaces Adonis:configure:interfaces> modify <eth0|bond0> Adonis:configure:interface:eth0> remove address 192.168.1.1/24 Adonis:configure:interface:eth0> save Saved interface successfully
Run the show interfaces command to verify the new Primary Service IP and that
the default IPv4 address has been removed from eth0/bond0.
Adonis> show interfaces eth0: Active = on eth0.1: IPv4 Addresses 192.0.2.100/24 (Primary) Active = on eth1: Active = on eth2: Active = off eth3 Active = off Dedicated Management = Enabled Management Interface = eth0.1 Service Interface = eth0.1
- New servers—from the Address Manager user interface, add the server (Servers tab > New).
- Previously managed servers—from the Address Manager user interface, Disable the server (Servers tab > server name > Disable) then replace the server (Servers tab > server name > Replace). From the Replace Server page, you must select the Reset services on remote DNS/DHCP Server check box due to changing the Services interface and Primary Service IP on the server.